BG1, PRELOAD BG2, PRELOAD

Results 1 to 4 of 4
  1. #1
    Future Mm Teamaker Weretigr's Avatar
    Points: 28,325, Level: 51
    Level completed: 71%, Points required for next Level: 325
    Overall activity: 0%
    7 days registered 1000 Experience Points 500 Experience Points 250 Experience Points 100 Experience Points
    PSN
    Weretigr
    Join Date
    Feb 2010
    Location
    North Lincolnshire
    Posts
    2,820
    Blog Entries
    1

    Default Sackbot Fall Damage

    Sitting on the bus this morning, I was thinking about how my holographic followers (controlinator, bumpers etc.) that followed the sackbot, seemed to fly off a little bit when you hit the ground at speed. I also recalled these holograms flying off completely when the followers' strengths were set to low.

    See where I'm going with this?

    What if you were to have a follower (set to say, 70% strength following a tag inside the sackbot) and a different tag (detected by a sensor which is also on the sackbot) on a piece of holo? If you hit the ground with considerable force, the tag will jerk out of range of the sensor.

    If you invert the tag sensor, then you can connect it to either a destroyer, or a counter and destroyer. If you use a counter, then you'll have to have an emitter re-emit the tag sensor for use again.

    If you want to have different sized falls create different damage, then use multiple 180° (down facing) sensors in rings* to detect when the tag enters that area.

    *ring consisting of max and min sensor range that are close together.


    This is only a theory, so it may not work... but there is a good chance it will. You'll probably need to tweak the follower's strength until you get the right effect. Let me know if you got it to work, and what changes you had to make!
    Last edited by Weretigr; 02-21-2011 at 03:44 PM.
    Be the one who nurtures and builds. Be the one who has an understanding and a forgiving heart. One who looks for the best in people. Leave people better than you found them.”
    — Marvin J. Ashton


    Contact me: @dayneoram

    LBPC MINECRAFT SERVER
    198.12.70.37:8123

    (May be discontinued.. It's been a while..)

  2. #2
    Sackperson Private piggabling's Avatar
    Points: 28,846, Level: 52
    Level completed: 18%, Points required for next Level: 904
    Overall activity: 0%
    7 days registered 5000 Experience Points 1000 Experience Points 500 Experience Points 250 Experience Points
    PSN
    piggabling
    Join Date
    Sep 2009
    Location
    Michigan, USA
    Posts
    2,438
    Blog Entries
    3

    Default

    Sounds like a good, promising idea to me.



  3. #3

    Default

    I've already designed a system like this, but never officially published it, & I've been thinking of adding it to a sackbot, so it could die if it falls too far or is hit too hard, but I don't really use sackbots much. The only problem this system has is that if you use a bounce pad set to a long enough distance, it could kill your sackbot if it jumps on it. It actually will work but, as I said before, you might want to make sure your bounce pads aren't too powerful. Also, I haven't tried this myself, but if you use a sackbot and then use a "death-less" teleporter I don't know if it would kill you or teleport you, so you might want to try it out.

  4. #4

    Default

    You could always design a system to toggle it on and off when you need it, so bounce pads wouldn't be an issue.

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •